DISH Network Error Codes – 3 and 4 Digit Error Code

By |

We have listed here the DISH Network Error Codes and How to Troubleshoot. Are you getting an error in your DISH Network. Find 3 digit, 4 digit and alphanumerical code. The Dish Network Error Code will help you in troubleshooting your DISH Receiver. DISH Network codes will come on your TV or on your DISH Receiver whenever there is an error.

DISH Network 3 Digit Error Code

DISH Network Error Code 01 : A problem was encountered when opening the files for this DVR event. Please note the Error Code 06
DISH Network Error Code 02 : A problem was encountered when opening the files for this DVR event. Please note the Error Code 06
DISH Network Error Code 03 : A problem was encountered when opening the files for this DVR event. Please note the Error Code 06
DISH Network Error Code 04 : A problem was encountered when opening the files for this DVR event. Please note the Error Code 06
DISH Network Error Code 05 : A problem was encountered when opening the files for this DVR event. Please note the Error Code 06
DISH Network Error Code 06 : A problem was encountered when opening the files for this DVR event. Please note the Error Code 06
DISH Network Error Code 07 : A problem was encountered when opening the files for this DVR event. Please note the Error Code 06
DISH Network Error Code 001 Your Receiver Can No Longer Control the Multidish Switch. For Technical Assistance, please select “Help”.
Please Call Technical Support for assistance: 1-800-333-3474.
DISH Network Error Code 002 The Satellite Signal has been lost, Signal acquisition is in progress. Please wait, or press the “UP”
or “DOWN” arrow button to change channels.
DISH Network Error Code 003 A problem has been detected with your Multi-Dish Switch. This can be caused by cable lengths of more
than 100 feet, or by using the wrong type of cable. RG6 is the recommended Type.
DISH Network Error Code 004 A problem has been detected with your Multi-Dish Switch. To continue to use your receiver, you must do
“Check Switch” test, available by selecting the “Multi-Dish Install” option in the Installation and Setup Menu.
Non-Dish Home Receivers – Replace “Multi-Dish Install” w/”Point Dish/Signal”
DISH Network Error Code 005 Your Smart Card does not currently have authorization to view or purchase this program. Please wait or
channel up or down.
DISH Network Error Code 006 Your purchase request cannot be completed. Please call the customer service center at: 1-800-333-Dish (3474)
DISH Network Error Code 007 Your purchase of this event is in the process of being authorized. Your receiver MUST BE connected to a
Phone Line. Please try again later. Press the “UP” or “DOWN” arrow button to change channels.
DISH Network Error Code 008 This is a DISH-ON-COMMAND event which you have already purchased, and is in the process of being
authorized. Your receiver MUST BE connected to a phone line. Please try again later.
DISH Network Error Code 009 The DISH-ON-DEMAND program is no longer available for purchase. Please check for the next available time.
Press the “UP” or DOWN” arrow button to change channels.
DISH Network Error Code 010 The DISH-ON-DEMAND program is no longer available for purchase. Please check for the next available time.
DISH Network Error Code 011 This Program has been blacked out in your area.
DISH Network Error Code 012 This program has been blacked out in your area. Press the “UP” or DOWN” arrow button to change channels,
or for further information press the “INFO” button.
DISH Network Error Code 013 This is a subscription chennel which has not been purchased. To purchase, please call: 1-800-333-DISH (3474)
Press the “UP” or DOWN” arrow button to change channels.
DISH Network Error Code 014 This is a subscription chennel which has not been purchased. To purchase,
please call the customer service center at:: 1-800-333-DISH (3474)
DISH Network Error Code 015 Acquiring Satellite Signal. Please Wait.
DISH Network Error Code 016 Access rights for this event cannot be obtained.
DISH Network Error Code 017 Acquiring access rights for this event. Please Wait.
DISH Network Error Code 018 The credit limit on your smart card has been exceeded. An authorization from the customer service center is
required. Your receiver MUST BE connected to a phone line. The call and authorization could take several
minutes.
DISH Network Error Code 019 The Smart Card is not inserted correctly.
DISH Network Error Code 020 The Smart Card currently Inserted is not valid for use with this receiver.
DISH Network Error Code 021 Please Insert your Smart Card.
DISH Network Error Code 022 Your receiver has not yet been authorized.
DISH Network Error Code 023 Unable to Acquire program guide information
DISH Network Error Code 024 Unable to access this feature at this time: data not Available.
DISH Network Error Code 025 ERROR The satellite signal has been lost, signal acquisition is in progress. Please wait, or press the “UP” or
“DOWN” arrow button to change channels.
DISH Network Error Code 026 ATTENTION Acquiring satellite signal. Please wait or press SELECT to continue watching your local channels.
DISH Network Error Code 027 The Satellite Signal has been acquired, all Satellite channels are now available.
DISH Network Error Code 028 Pay Per View Events cannot be purchased until the receiver has downloaded new software. Turn the receiver
off via the remote POWER button and do not disturb for the next 10 minutes.
DISH Network Error Code 029 Dish-On-Demand. To purchase, please call the customer service center at: 1-800-333-DISH (3474). To change
channels, press the “UP” or “DOWN” arrow button.
DISH Network Error Code 030 This is a special event which is not available for purchase. For further information press the “Info” button.
DISH Network Error Code 031 This is a special event which is not abailable for purchase. Channel “UP” or DOWN”, or for further information
press the “Info” button.
DISH Network Error Code 032 ERROR You have attempted to create a VCR event timer, but have not completed the VCR setup. The
VCR setup must be completed before a VCR event timer can be created. Do you wish to complete the VCR
setup now? (Yes/Cancel/No)
DISH Network Error Code 033 Information VCR set Date/Time request denied. VCR Time and Date information is currently synchronized with
the satellite signal.
DISH Network Error Code 034 ERROR Invalid Date
DISH Network Error Code 035 ERROR Invalid Time
DISH Network Error Code 036 ERROR You have selected the “Set Date/Time” option with no channel selected. Select the desired
channel for this event timer.
DISH Network Error Code 037 ERROR You have specified a timer end time which is exactly the same as the start time. You must enter an end
time which is at least one minute past the start time.
DISH Network Error Code 038 ERROR You have not entered valid start and end times for this timer. Please enter start and end times for this
timer before attempting to create it.
DISH Network Error Code 039 ERROR You have selected the “Edit” option with more than one timer selected. Select only the timer you want to
edit.
DISH Network Error Code 040 You have selected the “Edit” option without selecting a timer to edit. Highlight the timer to edit and press “Select”.
DISH Network Error Code 041 ATTENTION The maximum number of event timers has been reached. No more can be created at this time
without deleting one previously created.
DISH Network Error Code 042 ATTENTION The maximum number of event timers has been reached. No more can be created at this time
without deleting one previously created. Do you wish to delete one? (Yes/Cancel?NO)
DISH Network Error Code 043 You have entered a VCR code which is not in the data base. Please enter another code.
DISH Network Error Code 044 WARNING Ensure that your VCR is turned on, and a BLANK tape is inserted. This test will erase part of the tape?
DISH Network Error Code 045 ATTENTION The VCR test is in progress: your VCR should be recording.
DISH Network Error Code 046 ATTENTION The VCR test is in progress: your VCR should be stopped.
DISH Network Error Code 047 ATTENTION The VCR test is in progress: your VCR should be rewinding.
DISH Network Error Code 048 ATTENTION The VCR test is complete. You should have seen your VCR start recording, stop, then rewind.
If this didn’t happen, try another three-digit code from the user’s manual.
DISH Network Error Code 049 ERROR There is no cassette in the VCR
DISH Network Error Code 050 ERROR Recording on this cassette is not possible because the cassette’s safety tab has been removed.
DISH Network Error Code 051 ERROR A mechanical failure has occurred in the VCR. Please contact Echostar service.
DISH Network Error Code 052 Information EPG and Browse information is not available during Record or Play.
DISH Network Error Code 053 ATTENTION Please wait while critical information is loaded into the VCR.
DISH Network Error Code 054 ATTENTION The selected operation is not allowed in the current check mode.
DISH Network Error Code 055 Is the mounting and positioning of your Dish(es) complete, with a “locked” indication in the Point Dish and
Signal Strength Screen? (YES/Cancel/NO)
DISH Network Error Code 056 Is the mounting and positioning of your Dish(es) complete, with a “locked” indication in the Point Dish and
Signal Strength Screen? Is the switch correctly Installed? (YES/Cancel/NO)
DISH Network Error Code 057 Select “Check” to check switch installation. Select “View” to View Current Switch Setup. Select “Cancel”
to return to the previous menu. (Check/View/Cancel)
DISH Network Error Code 058 Please wait while your switch installation is checked. Currently doing Test #: ( 12 ) out of 18.
DISH Network Error Code 059 You have attempted to exit this screen without performing “Check Switch.” This check is required when a
multi-dish switch is installed. Perform the check now? (Yes/Cancel/No)
DISH Network Error Code 060 The signal you are receiving is not from the Satellite you have selected. Reposition the dish,
check the dish connection, or select the correct satellite. (Ok)
DISH Network Error Code 061 Vital Program Information will now be Downloaded into your receiver. Do Not Disturb or Unplug it.
Do Not disturb or unplug the receiver until this screen disappears. Programming vital program information into
receiver.
Vital Program Information will now be Downloaded into your receiver. Do Not Disturb or Unplug it.
Status: Downloading Information…
DISH Network Error Code 062 You Cannot Modify the “All Channels” List
DISH Network Error Code 063 You Cannot Modify the “All Channels” List name
DISH Network Error Code 064 Duplicate favorites list names are not allowed
DISH Network Error Code 065 Favorites list names must have at lease one character
DISH Network Error Code 066 The favorites list you are attempting to save contains no channels.
DISH Network Error Code 067 This action will completely erase this favorites list. Are you sure you want to do this? (Yes/Cancel/NO)
DISH Network Error Code 068 ERROR The auxiliary channel cannot be deteleted.
DISH Network Error Code 069 ERROR This channel name has already been used. Duplicate channel names are not allowed.
DISH Network Error Code 070 WARNING This action will completely erase the local channels list. Are you sure you want to do this?
(Yes/Cancel/NO)
DISH Network Error Code 071 WARNING A blank channel name can cause difficulty in the favorites lists, guide, etc. Are you sure you want to
do this? (Yes/Cancel/NO)
DISH Network Error Code 072 The password you just entered was not correct. Do you wish to try again? (Yes/Cancel/No)
DISH Network Error Code 073 The password you just entered does not match your original password. Do you wish to try again (Yes/NO)
DISH Network Error Code 074 The number of password entry retries has been exceeded. Please try again later.
DISH Network Error Code 075 The number of password entry retries has been exceeded. Press the “UP” or “DOWN” arrow button to change
channels.
DISH Network Error Code 076 This event is locked: To view, enter your password. To change channels, press the “UP” or “DOWN” arrow
button when “OK” IS highlighted.
DISH Network Error Code 077 The Front Panel buttons are locked.
DISH Network Error Code 078 To ensure continued availability of Dish-On-Demand programming, you must connect a phone line to the real
panel of your DISH receiver.
DISH Network Error Code 079 Please connect your receiver to your phone line or your ability to purchase PPV will be disabled sometime in
the future.
DISH Network Error Code 080 “The receiver needs to dial out so that the Smart Card records can be retrieved.”
DISH Network Error Code 081 Phone Line test in progress. Please Wait.
DISH Network Error Code 082 Phone Line Test PASSED.
DISH Network Error Code 083 Phone Line Test FAILED. Select YES to Re-Test. (Yes/Cancel/NO)
DISH Network Error Code 084 Dish-On-Demand. To purchase, press “SELECT”. To change channels press the “UP or “DOWN” arrow button.
DISH Network Error Code 085 You have indicated that you wish to purchase a Dish-On-Demand event. Is this correct? (Yes/Cancel/NO)
DISH Network Error Code 086 This is a Dish-On-Demand event which you have already purchased.
DISH Network Error Code 087 You made changes to the previous menu. Do you really want to abandon them? (Yes/Cancel/NO)
DISH Network Error Code 088 You made changes to the previous menu. Do you really want to abandon them? (Yes/Cancel/NO)
DISH Network Error Code 089 There are no mail messages.
DISH Network Error Code 090 There are currently no system upgrades available.
DISH Network Error Code 091 This feature is not available.
DISH Network Error Code 092 You have indicated that you wish to purchase new receiver features. Is this correct? (Yes/Cancel/NO)
DISH Network Error Code 093 This action will reset your current settings back to the factory defaults! Are you sure you want to do this?
(Yes/Cancel/NO)
DISH Network Error Code 094 The factory flag is set! This action will reset your current settings back to the factory defaults! Are you sure
you want to do this? (Yes/NO/Help)
DISH Network Error Code 095 Non-Volatile memory has been corrupted. It will be cleared after pressing the front panel power button
or by removing AC power from the receiver.
DISH Network Error Code 096 Warning: Your dish has been positioned for optimum at an angle different than you originally specified. Please
enter the following value on the elevation angle selector. Angle Selector: 58 OK
DISH Network Error Code 097 Error: The value entered on the elevation angle selector is invalid. Please enter a valid elevation angle.Refer to the
users manual for valid values. OK
DISH Network Error Code 098 Error: Unable to lock onto a signal within +/- 5 degrees of specified elevation. Ensure correct elevation angle has
been entered, your vehicle is level and there are no obstructions in front of the dish. Put the Datron controller into
stow mode.
DISH Network Error Code 099 Unable to calibrate dish movememt. Ensure that nothing is obstructing the movement of the dish, then put the
the Datron Controller in the stow mode.
DISH Network Error Code 100 Your Satellite Dish is being stowed. OK
DISH Network Error Code 101 Attention: Your Satellite Dis has been stowed. OK
DISH Network Error Code 102 Error: Unable to stow dish. Turn the power off then back on at the Datron Controller. Place the controller in stow
mode. OK
DISH Network Error Code 103 You have indicated that you wish to purchase a Dish-On-Demand event. Is this correct? (Yes/Cancel/NO)
DISH Network Error Code 104 A serious problem has been detected with your receiver. Please call: 1-800-334-7496.
DISH Network Error Code 105 Upgrade of all program information in progress. Do Not disturb your receiver while this screen is displayed.
DISH Network Error Code 106 Please install external switch bow now. After Installation, select “Continue”. If dish has an internal switch
box, select “Continue” to proceed. Select “Cancel” or “Back” to return to previous Menu. (Continue/Back/Cancel)
DISH Network Error Code 107 You have not completed the combo dish installation process. Continue with the Installation? (Yes/Cancel/NO)
DISH Network Error Code 108 SW42/Internal switch box has been detected. If switch type detected, check your switch installation and detect
again.
DISH Network Error Code 110 ERROR You have entered an HDTV code that is not supported. Please enter another code.
DISH Network Error Code 112 The Satellite Signal has been lost, Signal acquisition is in progress. Please wait, or press the “UP”
or “DOWN” arrow button to change channels.
DISH Network Error Code 113 The QAM frequency table is invalid. To continue to use your receiver, you must perform the QAM frequency
“Scan” test, available by selecting the “QAM Scan/Signal” option in the installation and Setup Menu.
DISH Network Error Code 114 Your receiver can no longer store QAM frequency results. Please contact your building maintenance personnel.
DISH Network Error Code 115 Have you successfully completed a QAM scan and have a “locked” indication in the QAM Frequency Scan
and Signal Strength Screen? (Yes/Cancel/NO)
DISH Network Error Code 116 Either a successful scan has not been completed or the signal is not locked. Rescan the QAM frequencies
or check your connections.
DISH Network Error Code 117 A successful scan has not been completed or the signal is not locked. Are you sure you want to exit the QAM
Frequency Scan and Signal Strength Screen? (Yes/Cancel/NO)
DISH Network Error Code 118 You have exceeded the total favorite channel Capacity. Remove some channels before adding more.
DISH Network Error Code 119 You are about to overwrite the current scanned QAM frequency table with the factory default table. If you select
yes, to resume normal user operation you will have to rescan. Continue? (Yes/Cancel?No)
DISH Network Error Code 120 You cannot receive this channel outside the designated viewing area.
DISH Network Error Code 121 ERROR Unable to access this feature at this time.
DISH Network Error Code 122 ERROR An internal communication failure has been detected. Press “Select” on your Remote Control
to reset your receiver. If this problem reoccurs, please call DISH Network (1-800-333-3474) for assistance.
DISH Network Error Code 123 Warning This action will reset all closed caption seetings back to the factory defaults! Are you sure you want to
do this? (Yes/Cancel/NO)
DISH Network Error Code 124 ATTENTION The internal smart card is not authorized for this receiver. Please call DISH Network
(1-800-333-3474) for assistance.
DISH Network Error Code 127 Your Smart Card is about to expire, and must be replaced. For more information, tune to channel 199
www.dishnetwork.com/smartcard, or call 1-888-651-2022
DISH Network Error Code 128 Your receiver is being authorized. Please do not disturb the receiver until this message has disappeared.
DISH Network Error Code 129 Your receiver has not yet been authorized. Please call 1-800-333-DISH (3474) for activation R00XXXX XXXX
S000 XXXX XXXX
DISH Network Error Code 151 A serious problem has been detected with your receiver. (ECM – Electronic Counter Measure)
DISH Network Error Code 153 A serious problem has been detected with your receiver. (ECM – Electronic Counter Measure)
DISH Network Error Code 155 A serious problem has been detected with your receiver. (ECM – Electronic Counter Measure)
DISH Network Error Code 301 ERROR System can not communicate with internal smart card. Please call 1-800-333-DISH (3474)
DISH Network Error Code 302 ERROR You have selected more than one event for the requested operation. Please select only one event
for this operation.
DISH Network Error Code 303 WARNING Your receiver’s memory is now being programmed. Do not disturb or unplug your receiver while
the green front panel light is blinking.
DISH Network Error Code 307 Attention The DVR recorded event playback is over. Please select one of the three options below. (Yes/Cancel/NO)
DISH Network Error Code 308 Attention This DVR recorded event playback has been stopped. Please select one of the four options below.
(Erase/Start Over/Resume/Live TV)
DISH Network Error Code 309 ERROR There is insufficient space left on the hard disk to perform the requested operation. Additional space can
be obtained by erasing old recorded events. Do you with to erase some now? (Yes/No/Cancel)
DISH Network Error Code 310 ERROR The hard disk is full. The recording in progress has been halted. Additional space can be obtained by
erasing old recorded events. Do you wish to erase some now? (Yes/No/Cancel)
DISH Network Error Code 311 ERROR A serious problem has been detected with your hard disk drive – error code: XXX Please call
DISH Network Error Code 1-800-333-DISH (3474)
DISH Network Error Code 312 ERROR Your request can only be carried out in live mode. Stop recording and switch to live mode now?
(Yes/No/Cancel)
DISH Network Error Code 313 ERROR The following time is about to fire: Event: Channel: There is a recording in progress which conflicts
with this timer. One of them must be stopped. Please select the one to stop.
DISH Network Error Code 314 ERROR Your request can only be carried out in live mode. Switch to live mode now? (yes/No/Cancel)
DISH Network Error Code 315 Information The hard disk file system has been re-initialized. It will be cleared after pressing the front panel power
button or by removing AC power from the receiver.
DISH Network Error Code 316 Information Part of the recorded event has been lost due to satellite signal loss.
DISH Network Error Code 317 ERROR You are currently viewing the event you are attempting to erase.
DISH Network Error Code 318 ERROR Program information on the hard drive is outdated. Retrieve program information from the Satellite Now.
DISH Network Error Code 319 ERROR Program information on the hard drive is outdated. There is a recording in progress. Temporarily stop
it and get info from the satellite now?
DISH Network Error Code 320 ERROR Program information on the hard drive is outdated. Recording in background is in progress. Temporarily
stop it and get info from the satellite now.
DISH Network Error Code 321 Attention Stop recording and switch to live mode now?
DISH Network Error Code 323 ERROR You cannot create a PVR timer for the channel you selected. Select a different timer.
DISH Network Error Code 324 ERROR Recording is in progress.
DISH Network Error Code 325 ERROR There are currently no calls in the log to delete.
DISH Network Error Code 326 Warning This will clear all the calls from the log. Are you sure you want to do this? (Yes/Cancel/No)
DISH Network Error Code 327 ERROR You have selected the “Delete” option without selecting a call to delete. Highlight the call to delete
and press “Select”
DISH Network Error Code 328 Attention The receiver is scheduled to download the latest recording in progress. Would you like to stop the
recording to receive the download? (Yes/No/Help)
DISH Network Error Code 329 Attention Your receiver is scheduled to download the latest program guide information to the hard disk. Continue
download now? (Yes/No/Help)
DISH Network Error Code 330 ATTENTION The program guide information is now being downloaded to the hard disk on your receiver.
Please wait or select “Stop Download” to hald the downloading of program guide information. This download
takes approximately five minutes.
DISH Network Error Code 331 There is a new, free system upgrade available. Do you wish to have it downloaded into your receiver?
Note: The software download will take 5 to 10 minutes!
DISH Network Error Code 332 Warning Program information on the hard disk is outdated. Would you like to retrieve progarm information from
the satellite now? This will take approximately five minutes. (Yes/No/Help)
DISH Network Error Code 333 Attention The program now showing on this channel is available for viewing without restrictions.
DISH Network Error Code 336 Attention A serious problem has been detected with your PVR data. To continue using PVR features, PVR must
be reinitialized. This will erase all previously recorded PVR events. Reinitialize PVR now? (Yes/No/Cancel)
DISH Network Error Code 337 No History Available.
DISH Network Error Code 338 ERROR No selection has been made. Please make a selection to continue.
DISH Network Error Code 342 The Interactive application is downloading, please wait or cancel.
DISH Network Error Code 343 The selection requires an update to DISH500 satellite dish. With your upgrade, you will get on-demand news,
entertainment, games and shopping. Call 1-800-333-DISH (3474)
DISH Network Error Code 344 A new DISH Interactive channel is coming soon. For info on new channels, see the DISH Interactive link at
dishnetwork.com
DISH Network Error Code 345 The Dish Home Channel Is Locked. To access, please select Dish Home from the program guide and enter your
password.
DISH Network Error Code 346 ERROR Low operating temperature error. XX Degrees F The satellite receiver is too cold to initiate operation
without causing potential damage to the internal Hard Disk Drive. The satellite receiver must warm to at leat 40F
before it will be operational. The satellite receiver will automatically reset itself once it has reached the minimum
operating temperature.
DISH Network Error Code 347 No History Available.
DISH Network Error Code 349 You are attempting to use a version of the Smart Card that is Incompatible with this receiver.
DISH Network Error Code 350 ERROR This is a virtual Channel. You cannot record this channel.
DISH Network Error Code 351 Confirmation Are you sure you want to erase the selected events?
DISH Network Error Code 355 Warning Your satellite receiver has exceeded the recommended operating temperature. Placing items on top of the
receiver or housing your receiver in an enclosed cabinet with limited airflow may cause this problem. Continued
operation at this temperature will damage the receiver.
DISH Network Error Code 356 Your DISH network Programming has been suspended. Pleace call 1-800-333-DISH (3474) to reactivate
your account.
DISH Network Error Code 357 Smart Card Replacement: Step 1: Verify the information below with the mailer to ensure a correct match of your
new /yellow card to this receiver. Receiver ID: R00 XXXX XXXX New Card ID: S00 XXXX XXXX
Step 2: Insert new/yellow cards into all receivers before continuing to Step 3. Step 3: Call 1-888-651-2022
or go to www.dishnetwork.com/smartcard to complete reactivation of your receiver(s).
DISH Network Error Code 358 Your receiver smart card Must be replaced. Insert your new smart card of call 1-800-333-DISH (3474).
DISH Network Error Code 359 To continue viewing this channel, a new card must be installed by MM/DD. Call 1-888-651-2022 for
questions or assistance. Press SELECT to view this channel or the UP or DOWN arrow buttons to change
channels.
DISH Network Error Code 360 To view this channel, a new card must be installed. Call 1-888-651-2022. If you have not received or need
assistance installing the new card.
DISH Network Error Code 361 To view this channel a new card must be installed. Call 1-888-651-2022. If you have not received or need
assistance installing the new card. Press the UP or DOWN arrow buttons to change channels.
DISH Network Error Code 362 Press “SELECT” to load this interactive channel or the “UP” or DOWN” arrow buttons to change channels.
DISH Network Error Code 363 The Pay-Per-View limit has been exceeded. To order Pay-Per-View at this time, call 1-877-DISH-PPV (3474-778)
DISH Network Error Code 366 Attention To continue viewing this channel, the receiver needs to dial-out at this time. Please connect a phone
line to the receiver and select YES to dial-out.
DISH Network Error Code 371 Upgrade This channel is available for Immediate upgrade without a call! Find out more by selecting “Continue”
DISH Network Error Code 378 Attention: Now Scanning for available satellites… Please wait
DISH Network Error Code 500 ERROR The Primary and Secondary Remotes are set to the same address. The addresses must be different.
Please change the address on one of the remotes (Primary Remote Address 3 – 1 UHF Pro and IR
Secondary Remote Address 3 – 2 UHF Pro
DISH Network Error Code 501 ERROR You are attempting to set the remote address of the TV 1 remote to 3, which is the same address as the
TV 2 remote. They MUSt be different. Please change the address of your TV 1 remote and try again.
DISH Network Error Code 502 ERROR A problem has been detected with your switch box configuration. If both tuners are being used, they must
both be connected to the same satellites. This problem could be caused by a faulty swith box or incorrect
connections. If the problem cannot be found or fixed, remove the satellite connection from one of the tuners.
This problem must be resolved before you can use your receiver. Please make the appropriate modifications
and exit this screen to view the results of the check switch test and run check
DISH Network Error Code 503 Attention: TV is performing a switch installation test. This will interrupt your live video until the switch installation
test is complete.
DISH Network Error Code 504 Warning TV 2 is currently in use. This operation will disrupt the use of the other TV. Do you wish to continue?
DISH Network Error Code 505 Attention: TV 1 has switched the receiver into Single User Mode. You will no longer have control of this TV.
DISH Network Error Code 507 Attention This option is currently in use by TV 1 You may continue and view the screen, but no changes can be
made at this time. Do you wish to continue?
DISH Network Error Code 508 Attention One or more events are currently in use and cannot be deleted at this time. Please try again later.
DISH Network Error Code 510 Dish Home Interactive TV is in use on the other TV. Please try again later.
DISH Network Error Code 513 Attention The system will now power down to check for important system upgrades. Select “NO” or “Cancel”
to continue viewing TV.
DISH Network Error Code 514 Attention: The receiver is about to be turned off due to inactivity. Select “No” or “Cancel to continue viewing TV.
Yes/Cancel/No
DISH Network Error Code 520 Attention: The timer you are attempting to delete has already started the recording process. Do you wish to stop
The recording and delete the timer? Yes/Cancel?No
DISH Network Error Code 521 Warning Errors have been detected on your hard drive. Your hard drive MUST be cleaned. This will only take a
few minutes. You may choose to clean your hard drive now. You MUST clean your hard drive within 7 days,
or it will be cleaned automatically. You can clean it later by boing to the Menu, System Setup, Diagnostics, and
then Hard Drive. Important When your hard drive is cleaned, ALL of your recorded events will be deleted !!!
DISH Network Error Code 526 Warning Errors have been detected on your hard drive. Your hard drive MUST be cleaned. This will only take a
few minutes. You may choose to clean your hard drive now. You MUST clean your hard drive within 7 days,
or it will be cleaned automatically. You can clean it later by boing to the Menu, System Setup, Diagnostics, and
then Hard Drive. Important When your hard drive is cleaned, ALL of your recorded events will be deleted !!!
DISH Network Error Code 527 ATTENTION Your hard drive is being repaired. This will take a few minutes. Do NOT disturb your receiver until
the repair has been completed. When the repair has completed, your receiver will be restarted.
DISH Network Error Code 530 Warning One of the satellite inputs or switches is not connected properly. Normal operation will be
Adversely affected.
DISH Network Error Code 531 Attention Please wait while we search for events that match your request.
DISH Network Error Code 532 Timer Conflict Resolution There are multiple conflicts with the timer you are about to create, some of the episodes
may not be recorded. Please selec a method to resolve these conflicts. Automatically resolve by priority
Change the priority of this timer.
DISH Network Error Code 534 Attention: Are you sure you want to delete these timers? Yes/Cancel/No
DISH Network Error Code 587 ATTENTION To continue please connect an operational phone line to the receiver and press “Select” on the
Remote Control.
DISH Network Error Code 588 ATTENTION If you wish to eliminate the $4.99 per month additional outlet/programming access fee, this
receiver must be continuously connected to an operational phone line.
DISH Network Error Code 590 ERROR You are attempting to set both remoted to the same address. You are not allowed to do this.
Please select another remote address for one of the two remote addresses.
DISH Network Error Code 599 Hard Disk Diagnostics Critiacl Test in Progress. Minutes X Elapsed This test will take up to 45 minutes.
Running Disk Diagnostics Cancelling will reset the receiver.
DISH Network Error Code 600 A check switch has been performed, but the results are not valid. The problem must be fixed and a valid switch
matrix must exist before exiting Point Dish.
DISH Network Error Code 601 Attention You have not performed a check switch. Are you sure you want to exit Point Dish?
DISH Network Error Code 602 ERROR Point Dish can not be run since a tuner can not be acquired for either Sattllite Input 1 or Satellite Input 2.
DISH Network Error Code 603 ERROR Point Dish can not get the selected tuner (Satellite Input 1)
DISH Network Error Code 604 ERROR Point Dish can not get the selected tuner (Satellite Input 2).
DISH Network Error Code 605 ERROR No satellites are in the switch matrix. Please check the antenna and switch connections.
DISH Network Error Code 606 ERROR An invalid satellite was detected in the switch matrix. Please check the antenna alignment.
DISH Network Error Code 607 ERROR An X in the switch matrix is indicating that there is a problem. Please check all switches, connections,
and wires between the dish and the receiver.
DISH Network Error Code 608 The switch matrix indicated that there is a problem. Either the satellite columns on a legacy switch are not
adjacent or there is a problem in the transponder descriptions. Please check the connections and switches.
DISH Network Error Code 609 ERROR Point Dish is unable to complete the Check Switch test. Please check all connections and switches.
Point Dish will exit now. Please pull the power plug and then plug it back in.
DISH Network Error Code 610 ERROR The switch matrix indicates that there is a problem. When counting the columns, there is a mismatch
on the number of ports and entries in the matrices. Make sure both tuners have the same inputs and switch
configurations.
DISH Network Error Code 611 One of two problems exist. Either the DISPRO switch has transponder coverage that is not ALL, or a legacy
switch has a transponder coverage that is not EVEN and ODD.
DISH Network Error Code 612 ERROR Point Dish has failed due to an internal error and cannot recover.
DISH Network Error Code 613 ERROR The switch Matrices are not equivalent. Make sure that each tuner has the same switch setup and the
same satellite inputs.
DISH Network Error Code 614 ERROR There are too many columns in the DISHPRO switch matrix. There is a serious problem and this receiver
may not work properly.
DISH Network Error Code 615 ERROR There are too many columns in the legacy switch matrix. This is a serious problem and this receiver may
not work properly.
DISH Network Error Code 616 ERROR The connections to the DISHPRO switch are not standard. This configuration may not work properly.
DISH Network Error Code 617 ERROR The connections to the legacy switch are not standard. This configuration may not work properly.
DISH Network Error Code 618 ERROR The Satellites shown in the legacy switch matrix are not in adjacent columns. This indicates a
connection problem from the dish to the switch. The receiver will not operate properly when connected in this
fashion.
DISH Network Error Code 619 ERROR There is something wrong with the transponders in the switch matrix. It could be wrong EVEN/ODD pairs
or the transponders may be undetectable by the receiver. Check the switch, the LNBF, and the satellite
dish connections.
DISH Network Error Code 620 ERROR When checking the columns in a DISHPRO switch matrix, the connectiond did not appear to be correct.
This receiver may not work properly in this configuration.
DISH Network Error Code 621 ERROR When comparing two DISHPRO switch matrices, they do not match. This receiver will not work
correctly in this configuration.
DISH Network Error Code 622 ERROR When comparing two DISHPRO matrices, they do not match. They do not have the same satellites
represented. This receiver will not operate correctly in this configuration.
DISH Network Error Code 623 ERROR When comparing two legacy matrices, they do not match. They do not have the same number of
columns. This receiver will not work correctly in this configuration.
DISH Network Error Code 624 Error When comparing two legacy matrices, they do not match. There is a transponder coverage mismatch. This
receiver will not work properly in this configuration.
DISH Network Error Code 625 Point Dish can not be run since one of the tuners is being used by a higher priority task. Please try Point Dish
again later.
DISH Network Error Code 626 ATTENTION Point Dish has been started with a recording session in progress. Do you want to STOP the
recording and continue with Point Dish?
DISH Network Error Code 627 ATTENTION Your receiver is currently being updated. Your receiver will reset when the update is complete.
Please Wait….
DISH Network Error Code 628 ATTENTION An update has been acquired for your receiver. Press “Yes” to install now or press “No” to install
the next time your receiver is powered off.
DISH Network Error Code 629 ATTENTION This feature is being acquired from the satellite. Please stand by or check back in a few minutes.
DISH Network Error Code 630 ATTENTION There was a problem with your software upgrade. Please unplug your receiver and plug it in again.
DISH Network Error Code 633 ERROR A problem has been detected with your multidish switch. To continue to use your receiver you must do the
“Check Switch” test. Push the “Menu” button. Select “System Setup”. Select “Point Dish”. Select “Check
Switch”. Select “Check”.
DISH Network Error Code 634 ATTENTION DISH-ON-DEMAND. To purchase, please call the customer service center at: 1-800-333-DISH (3474).
DISH Network Error Code 635 ERROR A serious problem has been detected with your hard disk drive. Please call 1-800-333-DISH (3474)
DISH Network Error Code 636 ERROR The satellite signal has been lost, signal acquisition is in progress. Please wait, or press the “UP” or
“DOWN” arrow button to change channels.
DISH Network Error Code 637 ERROR Point Dish can not get a signal strength on this tuner (Satellite Input 1).
DISH Network Error Code 638 ERROR Point Dish can not get a signal strength on this tuner (Satellite Input 2).
DISH Network Error Code 639 ERROR When comparing two legacy switch matrices, they do not match. Different satellites are seen by each
of the two tuners. This receiver will not operate correctly with this configuration.
DISH Network Error Code 640 ERROR When comparing legacy switch and a DISHPRO switch, the number of columns per satellite does not
correspond. This receiver will not operate properly in this configuration.
DISH Network Error Code 641 ERROR When comparing a legacy switch and a DISHPRO switch, the DISHPRO switch does not cover ALL
transponders on a satellite. This receiver may not work correctly in this configuration.
DISH Network Error Code 642 ERROR When comparing a legacy switch and a DISHPRO switch, the legacy switch has the wrong number of
columns represented. This receiver will not work correctly in this configuration.
DISH Network Error Code 643 ERROR When comparing a legacy switch and a DISHPRO switch, the legacy switch does not cover all of the
transponders that it should. This receiver will not work correctly in this configuration.
DISH Network Error Code 644 ERROR When comparing a legacy switch and a DISHPRO switch, different satellites are seen on each tuner.
This receiver will not work correctly in this configuration.
DISH Network Error Code 645 ERROR When comparing a legacy switch and a DISHPRO switch, there are differences that will prevent this
receiver from working correctly.
DISH Network Error Code 646 ERROR The satellites seen by this receiver are not correct for the smart card being used. Point the Satellite
dish at the correct satellites for which the smart card is authorized.
DISH Network Error Code 647 ERROR This receiver can not lock either Satellite Input. A check switch can not be performed until at least one
tuner can get a signal lock.
DISH Network Error Code 648 Attention This action will reset your current settings to factory defaults and restart your receiver. This may take up
DISH Network Error Code 5 minutes. Are you sure you want to do this?
DISH Network Error Code 649 ERROR You have specified more digits for the prefix code than you entered. Please enter all digits or correct the
number of digits you are entering.
DISH Network Error Code 650 ERROR You have selected the “Set Time” option with no channel selected. Select the desired channel for this
event timer.
DISH Network Error Code 651 ERROR You must enter three digits for the VCR code.
DISH Network Error Code 652 ERROR The end time entered has already passed. Please enter a time later than now.
DISH Network Error Code 653 ERROR The timer you are attempting to edit has already started the recording process. You must stop the
recording, then return here to delete or modify it.
DISH Network Error Code 654 Information The system must be locked for locks to take effect.
DISH Network Error Code 655 Information In order to lock the system, you must enter a password.
DISH Network Error Code 656 Warning You have requested an NVM reset. This will take place during the next power up of the receiver. Do you
really want to do this?
DISH Network Error Code 657 Attention This is a special event which is not available for purchase.
DISH Network Error Code 658 ATTENTION DISH-ON-DEMAND. To purchase, please call the customer service center at: 1-800-333-DISH (3474).
DISH Network Error Code 659 Attention Are you sure you want to remove all the selected items from the disk?
DISH Network Error Code 662 ERROR The VCR test failed.
DISH Network Error Code 663 Attention The receiver needs to dial-out to update the smart card records beford purchase can be completed.
Please connect your phone line to the receiver and select YES to dial-out.
DISH Network Error Code 664 Information Dialing… Please Wait
DISH Network Error Code 665 Information No dial tone. The receiver is unable to dial-out. Select YES to try again.
DISH Network Error Code 666 Information Dial-out failure. The receiver is unable to dial out. Select YES to try again.
DISH Network Error Code 667 Information Connecting…. Please Wait
DISH Network Error Code 668 Information Smart Card update successful.
DISH Network Error Code 669 The smart card detected does not appear to be valid. Please remove the smart card and insert it again,
or, insert the correct smart card. This will cause the system to restart and will take approximately 5 minutes.

READ  [SOLVED] How To Fix Leaking Water Shut Off Valve Under Kitchen Sink

DISH Network Error Codes

DISH Network Error Codes

DISH Network Error Code 671 Attention The Pay-Per-View free period has ended. To continue watching this event, it must be purchased.
DISH Network Error Code 672 Attention You have selected the “delete” option without selecting a timer to delete. Highlight the timer to delete
and then press the “Select” button.
DISH Network Error Code 673 ERROR You are currently viewing the event you are attempting to delete.
DISH Network Error Code 674 Attention Are you sure you want to revert to the previous version of installed software? You will lose all
recordings and preferences.
DISH Network Error Code 675 Attention Are you sure you want to revert to the factory installed software? You will lose all recordings and
preferences.
DISH Network Error Code 676 Attention The programming in your picture in picture (PIP) window has changed and is locked, blacked out, or not
purchased. Press the “UP” or “DOWN” arrow button to change channels.
DISH Network Error Code 677 Attention The last picture in picture (PIP) channel was locked, blacked out, or not purchased. Changing channel
Automatically.
DISH Network Error Code 678 Attention Acquiring data from satellite. Please wait…
DISH Network Error Code 679 Attention The event you selected was not recorded. Please delete this event. It is not viewable.
DISH Network Error Code 680 Attention Receiver is in stand-by. Booting
DISH Network Error Code 681 Information PVR events may take some time to delete. Please wait while the programs are deleted.
DISH Network Error Code 682 Attention You are creating a timer that will record for over 24 hours! Is this correct?
DISH Network Error Code 683 Information Installing new software. Please wait…
DISH Network Error Code 687 ERROR The satellite inputs to your receiver are connected incorrectly. Please chedk to make sure both inputs
have identical satellite feeds.
DISH Network Error Code 688 Warning A low battery condition has been detected in your remote. Please replace the batteries.
DISH Network Error Code 689 Information Your putchase history will only show current purchases not yet reported to the call center. Earlier
purchase history data has been lost. This will not cause problems with the operation of your receiver.
DISH Network Error Code 690 Attention The last channel was locked, blacked out, or not purchased. Changing channel automatically.
DISH Network Error Code 691 Attention You can not tune to channel 0 in both the main TV window and the PIP TV window. Automatically
tuning to another channel.
DISH Network Error Code 692 Error The program for this timer event is blacked out, not available, or the channel is no longer authorized.
DISH Network Error Code 701 Attention Only one Auto Tune timer can be set up for any given time.
DISH Network Error Code 702 Information Weather can only be used if there is 110 satellite reception on this receiver. The switch matrix
for this receiver indicates that you do not currently receive this satellite.
DISH Network Error Code 703 Information Starting receiver. Please wait….
DISH Network Error Code 704 Information A timer tried to fire and can not while this screen is active. The timer will fire when this screen is
closed.
DISH Network Error Code 705 ERROR The maximum number of minutes allowed for before and after a record timer event is 29 minutes. Please
DISH Network Error Code Enter another value.
DISH Network Error Code 738 Attention Please press the RECORD key on your TV2 remote to match its address to your receiver. This will
DISH Network Error Code Enable the TV2 remote to control the receiver. The TV2 remove is identified by its blue key with the number 2.
DISH Network Error Code 740 Attention: Select “YES” to load Dish Home Interactive TV. Yes/Cancel/No
DISH Network Error Code 743 Attention: This program is not available for viewing in your area. Select “OK” to go back or select “Help” for more
information Cancel/OK/Help
DISH Network Error Code 744 Attention: This program is not available for viewing in your area. Select “OK” to go back, press the “Up” or “Down”
arrow to change channels or select “Help” for more information. OK/Cancel/Help
DISH Network Error Code 760 The content of your hard drive has become corrupted and will cause your receiver to function inproperly. In order
for your receiver to function properly, all content on the hard drive will need to be deleted at this time. We apologize
for the inconvenience. Delete Now
DISH Network Error Code 761 Attention: All content on the hard drive has been successfully deleted. Your hard drive is clean of all corrupt
content. Your receiver will now function properly. OK
DISH Network Error Code 765 Attention To activate your receivers HD functionality, please call 1-800-333-Dish (3474).
DISH Network Error Code 801 ATTENTION Pay-Per-View limit has been exceeded. To order Pay-Per-View at this time, call 1-877-DISH-PPV
DISH Network Error Code 833 Attention: A problem has been detected, please wait while we check your switch.Performing test # 1 of 3 Cancel
DISH Network Error Code 834 Warning: The check switch test has been stopped and you may continue to experience problems. Please select
Retest to run check switch again. Cancel/Retest/Help
DISH Network Error Code 835 Error: A problem has been detected with your Satellite connectios. If the weather is bad please wait until the
weather passes and run check switch again. Cancel/Restart/Help
DISH Network Error Code 836 Warning: The check switch has found you have fewer satellites than previously detected. Press “Cancel” to keep
the old result, or save to save the new result. Cancel/Restart/Save
DISH Network Error Code 837 Attention: You will now be directed to the customer support channel to pay your bill. Once in the customer
support channel please choose option 3. Cancel/Pay Now/OK
DISH Network Error Code 838 Attention: Pocket Dish Events are now being deleted. Please Wait
DISH Network Error Code 840 Warning: Do you really want to delete the Pocket Dish Events? Yes/Cancel/No
DISH Network Error Code 842 Attention: Sending selected recordings to your Pocket Dish. Estimated time remaining 0HR 1MIN 50SEC Stop
DISH Network Error Code 851 Attention: You have connected too many devices to your USB port. System will only support one of them. OK
DISH Network Error Code 852 Attention: You have connected a Multimedia device to the USB port.Would you like to view and manage its content
at this time? Yes/No/Help
DISH Network Error Code 854 Attention: All files are successfully transferred to your receiver. OK
DISH Network Error Code 857 Attention: Deleting selected files, please wait…..
DISH Network Error Code 858 Attention: Loading file list from the device, please wait……
DISH Network Error Code 862 Attention: Sending selected recordings successfully completed. Estimated time remaining 0HR 1MIN 50SEC Done
DISH Network Error Code 863 Information: This feature is currently not supported. OK

READ  Best Way To Secure A Sliding Glass Patio Door Cheap and Fast

DISH Network Error Codes 4 Digit
0551 ERROR A serious problem has been detected with your hard disk drive – error code: XXX Please call
1-800-333-DISH (3474) May also Display as Error 0551
1038 ERROR A serious problem has been detected with your hard disk drive – error code: XXX Please call
1-800-333-DISH (3474) May also Display as 040E
1088 ERROR A serious problem has been detected with your hard disk drive – error code: XXX Please call
1-800-333-DISH (3474) May also Display as 0440
1111 ERROR A serious problem has been detected with your hard disk drive – error code: XXX Please call
1-800-333-DISH (3474) May also Display as 0457
1268 ERROR A serious problem has been detected with your hard disk drive – error code: XXX Please call
1-800-333-DISH (3474) May also Display as 04F4
1288 ERROR A serious problem has been detected with your hard disk drive – error code: XXX Please call
1-800-333-DISH (3474) May also Display as 04EE
9205 Unable to connect to Dish Network at this time. Your phone line may be in use or is not connected to your receiver.
Do you want to try again? Yes/No/Cancel
ATTENTION ATTENTION There is a new, free system upgrade available. Do you wish to have it downloaded into your receiver?
Note: The software download will take 5 to 10 minutes!
ATTENTION MODE Attention In addition to the “*” button on the remote for changing HD zoom Modes. “Page UP” changes HD
zoom modes. “Page Down” changes SD zoom mode.
ATTENTION UPGRADE ATTENTION There is a new, free system upgrade available. Do you wish to have it downloaded into your receiver?
Note: The software download will take 5 to 10 minutes!
DISH Network Error Code E205 Account Validation Error (Modem Error (205) Select retry to try again, or cancel to reenter your TVG account ID
or PIN. TVG Customer Relations 1-888-PLAYTVG (752-9984)
DISH Network Error Code E217 Unable to connect to Dish Network because your phone line is in use or not connected to the receiver
If problem persists, run a diagnostic check of the connection via the System Setup. Do you want to try again?
(Yes/No/Cancel)
DISH Network Error Code E300 Service Unavailable, Dish Home is currently unavailable. Please try again later. Thank You.
DISH Network Error Code E301 Attention: The selection you requested is currently unavailable. Please make another selection or try again later.
DISH Network Error Code E302 Attention: An unexpected error occurred. Press SELECT to return to Dish Home.
DISH Network Error Code E303 Attention: This selection requires an upgrade to a DISH500 satellite dish. With your upgrade, you will get
on-demand news, entertainment, games and shopping. Call 1-800-333-DISH (3474)
DISH Network Error Code E304 Attention: This selection requires a subscription which has not been purchased. To purchase, please call
1-800-333-DISH (3474).
DISH Network Error Code E305 Attention: The feature you are trying to access is not yet available on this receiver. Check back periodically to
see if this new feature is available to you!!!
DISH Network Error Code E306 Attention: The number of password entry retries has been exceeded. Please choose another menu selection.
DISH Network Error Code E307 Attention: This selection has been blacked-out in your area.
DISH Network Error Code E308 Error: The password you entered is incorrect. Do you wish to try again?
DISH Network Error Code E309 Outage, TV MAG will no longer be available to DISH Network Subscribers starting Wednesday September 29th
Look for more exciting applications coming soon to dish home!
DISH Network Error Code E321 This service is locked. To view, enter your password:
DISH Network Error Code E322 The password you entered is incorrect. Do you wish to try again? (Yes/NO/Cancel)
DISH Network Error Code E323 The number of password entry retries has been esceeded.
DISH Network Error Code E324 This is a subscription channel which has not been purchased. To purchase please call: 1-800-333-DISH (3474).
DISH Network Error Code E325 This selection requires a Dish 500 installation. To upgrade your installation, please call 1-800-333-DISH (3474).
DISH Network Error Code E326 Dish Election 2004 Coverage is currently not available. Please try again later.
DISH Network Error Code E327 The selected channel is currently not available.
DISH Network Error Code E328 Select “YES” to exit this service and resolve normal remote control functionality. Select “NO” to retain the
interactive functions. Press “SELECT” in full screen video to return to the Dish Election 2004 Coverage main menu.
DISH Network Error Code E365 Error Prossing Bets User cancelled Transaction. (E365) Select retry to try again, or cancel to return to the
Bet processing screen. TVG Customers Relations 1-888-PLAYTVG (752-9984) (Retry/Cancel/Help)
DISH Network Error Code EA01 Error The receiver is not associated with a residential account. Only residential accounts have access to
Customer Support.
DISH Network Error Code EA02 Error Your Dish Ntwork account is currently inactive. Your account information is currently not available.
DISH Network Error Code EA03 We are experiencing technical difficulties at this time and are unable to complete your request. Please try
again later.
DISH Network Error Code EA04 Please wait – this may take a few moments.
DISH Network Error Code EA05 We are unable to process your request at this time because we are unable to determine the account. Please
Call 1-800-333-DISH (3474) for account assistance
DISH Network Error Code EA06 Unable to connect to Dish Network because your phone line is in use or not connected to the receiver
DISH Network Error Code EA08 Dialing, please wait.
DISH Network Error Code EA09 ERROR Unable to connect to Dish Network at this time. Please try again later.
DISH Network Error Code EA10 ERROR The password you just entered was not correct. Do you wish to try again? (Yes/Cancel/NO)
DISH Network Error Code EA12 ERROR The number of password entry retries has been exceeded. Access to your account cannot be
Granted at this time.
DISH Network Error Code EA13 Your Customer Support features are currently not password protedted. For more information on how to lock
Customer Support select “Lock”. (Continue/Lock/Back)
DISH Network Error Code EA14 Press the Menu button to display the main menu. Select the Locks option (#5) to display the Parential and
Systems Locks menu. Note: If the receiver displays a message prompting you to enter a password, the
receiver has already been locked. Select the Lock System (3#) option to lock your receiver. The receiver displays
a message prompting you to enter a password. Note: If this option appears as Unlock System Instead, the
receiver is already locked.
DISH Network Error Code EA15 Please Wait
DISH Network Error Code EA21 We are unable to access the requested statement at this time. You may try again later, access your statement
at www.dishnetwork.com or call the Customer Service Center at 1-800-333-DISH (3474)
DISH Network Error Code EA22 No new activity has been posted since your last statement. New programming purchases and payments may
take up to 48 hours to appear here. Please check again in 48 hours if a recent transaction is not displayed.
DISH Network Error Code EA23 Today’s new programming purchase may take up to 48 hours to be displayed. Please check back later.
DISH Network Error Code EA25 Please wait – this may take a few moments.
DISH Network Error Code EA26 No more historical statements are available for this account. To discuss historical statements with a Customer
Service Representative, please contact the Customer Service Center at 1-800-333-DISH (3474).
DISH Network Error Code EA29 Please Wait
DISH Network Error Code EA32 Please wait while we locate your important messages.
DISH Network Error Code EA35 Thank you for selecting “Showtime Unlimited”. We noticed you do not have the ability to view all channels
available in this package because you do not have a dish pointed at the 119 satellite. You will be able to view
some of the channels in this package. If you would like to view all channels in this package, a dish pointed at
the 119 and 110 satellites location is required. To upgrade your install, call 1-800-333-DISH (3474)
(Remove Package/Keep Package/Back)
DISH Network Error Code EA36 ERROR Your account indicated that a payment mubt be applied in order to complete your programming upgrade.
Do you wih to make the payment now and continue with your upgrade? (Yes/Cancel/NO)
DISH Network Error Code EA37 ERROR Your purchases cannot be completed due to an outstanding request on your account. Please call
1-800-333-DISH (3474) for account assistance.
DISH Network Error Code EA38 Your request for Showtime Unlimites was successful! Enjoy your new programming and thank you for watching
DISH Network.
DISH Network Error Code EA39 Due to technical difficulties, your request cannot be processed. Please call 1-800-333-DISH (3474) for account
assistance.
DISH Network Error Code EA40 ERROR Your purchase cannot be completed. Please call 1-800-333-DISH (3474) for account assistance.
DISH Network Error Code EA45 ERROR The credit card number, type, or expiration date is incorrect. Please change or complete this information
and resubmit your payment request. (VISA/Master Card/American Express/Discover)
Credit Card Number XXXXXXXXXXXXXXXX Expiration Date: XXXXXXX (Pay/Back/Help)
DISH Network Error Code EA46 ERROR The amount hou have entered for the “Amount to Pay” is less than the “Amount Due”. The
“Amount to Pay” must be at least as much as the “Amount Due”
DISH Network Error Code EA47 ERROR A minimum amount of $2.00 is required.
DISH Network Error Code EA48 You cannot pay more then $.00
DISH Network Error Code EA49 Your services are not currently active. Would you like to restart services now for an additional $25.00 restart fee?
(OK/Cancel/NO)
DISH Network Error Code EA50 Your services are not currently active. You must pay at least $13.00 and your services will be automatically
reactivated within 10 minutes.
DISH Network Error Code EA51 We are unable to proceed with your request. Please contact the Customer Service Center at 1-800-333-DISH (3474)
DISH Network Error Code EA52 Your total amount due including the restart fee is $35.00. Programming will be automatically reactivated within e
minutes from making this payment.
DISH Network Error Code EA53 You have elected not to restart services. To restart services later, the $25.00 restart fee is required. Your amount
due now without the restart fee is $13.00.
DISH Network Error Code EA54 We are unable to proceed with your request. Please contact the Customer Service Center at 1-800-333-DISH (3474)
and be sure to say that you are trying to add programming.
DISH Network Error Code EA55 Please wait while your payment is being made.
DISH Network Error Code EA56 Your Programming will be reactivated shortly. Please wait.
DISH Network Error Code EA57 We are experiencing technical difficulties at this time. Try again from your receiver in a few moments, try us through
the Internet at www.dishnetwork.com, or call 1-800-333-DISH (3474) and follow the voice prompts for “Current
Customer” then “Make Payment” to apply payment automatically.
DISH Network Error Code EA58 ERROR We are unable to complete your payment with the credit card you selected. Do you wish to try another
credit card? (OK/Cancel/No)
DISH Network Error Code EA59 Your programming reactivation and payment of $10.00 was successful. Your new programming should be
available within 10 minutes. Your authorization number is XXXXXX. Your next statement will reflect two months
of programming charges to synchronize with our 30 days in advance billing policy. For complete billing
information, please see the Terms & Conditions section. Thank you for your payment and for watching Dish
Network! (OK/Terms & Conditions/Cancel).
DISH Network Error Code EA61 Your payment of $9.00 was applied successfully. Your authorization number is XXXXXX. Please keep this
number for your records. Thank you for your payment and for watching DISH Network!
DISH Network Error Code EA62 Payment of $10.00 was successful. Your authorization number is XXXXXX. Thank you for your payment. To
Continue with Credit Card AutoPay set up, select Continue.
DISH Network Error Code EA65 Please wait momentarily while we update your Credit Card AutoPay Information.
DISH Network Error Code EA66 Do you wish to receive your statement in the mail while your account is set up with Credit Card AutoPay?
By selecting NO you will not receive notification when each statement is ready, but statements can be viewed 24
hours a day here on your TV through Customer Support or online at www.dishnetwork.com (Yes/No/BACK)
DISH Network Error Code EA67 Your Credit Card AutoPay was successfully established. Thank you for using Credit AutoPay and enjoy
uninterrupted DISH Network programming!
DISH Network Error Code EA68 Your Credit Card AutoPay was successfully updated. Thank you for using Credit Card AutoPay and enjoy
uninterrupted DISH Network programming!
DISH Network Error Code EA69 We are unable to apply the credit card to your account as submitted. Please update this credit card
Information or try another card.
DISH Network Error Code EA72 Please wait while we set up your account with Credit Card AutoPay.
Transfer Progress Transfer Progress: Transferring Photos to your receiver. Complete 1 of 49 View TV/Stop/Cancel
Warning Warning Retrieving program information from satellite. Please wait or cancel.

READ  How To Block Out Light from Bedroom Window To Sleep Better?

 DISH Network Error Codes Video

We hope that now you are able to resolve your issue using DISH Network Error Codes. Please do visit our website for more troubleshooting.

Please follow and like us:

Leave a Reply

Your email address will not be published. Required fields are marked *